با سلام خدمت کاربران در صورتی که با خطای سیستم پرداخت بانکی مواجه شدید از طریق کارت به کارت (6037997535328901 بانک ملی ناصر خنجری ) مقاله خود را دریافت کنید (تا مشکل رفع گردد).
دسته بندی:
متالوژی - Metallurgy
سال انتشار:
2014
ترجمه فارسی عنوان مقاله:
شبیهسازی عددی فرآیند سوراخکاری لبهدار ورقه آلومینیوم
عنوان انگلیسی مقاله:
Numerical Simulation of Hole-flanging Process of Aluminum Sheet
منبع:
International Journal of Engineering and Technical Research (IJETR) ISSN: 2321-0869, Volume-2, Issue-7, July 2014
نویسنده:
Ibrahim Jallouli, Khaled Rouabeh, Slimen Attyaoui
چکیده انگلیسی:
A hole-flanging operation on a flat circular sheet
with a hole in the center is simulated by an incremental
elasto-plastic finite-element method, which incorporates
strain-hardening and isotropy, with care taken to describe the
boundary conditions of penetration, separation and the
alternation of the sliding sticking state of friction. The
simulation clearly demonstrates the processes of generation of
deformation shape until unloading. In the course of analysis, if
blank thickness is equal to fractured thickness, it is considered
that the forming limit of the flange has been reached.
The experimental results were compared with FEM-simulated
results. It is found that using the elasto-plastic FEM can
effectively predict the generation process of the deformed shape
until unloading. The calculated sheet geometries and the
relationship between punch load and punch travel are in good
agreement with the experimental data.
Index Terms: Elasto-plastic | finite element method | hole-flanging & metal forming.
چکیده فارسی:
عملیات سوراخکاری لبهدار بر روی یک ورقه تخت دایرهای شکل با یک سوراخ در وسط بوسیله یک روش المان محدود الاستوپلاستیک افزایشی شبیهسازی شده است که سختی کرنش و همسانگردی را با هم ترکیب میکند و با دقت به شرح شرایط مرزی نفوذ ، جدایی و تناوب حالت چسبندگی - لغزشی اصطکاک شبیهسازی شده است . شبیهسازی بطور واضحی فرآیندهای ایجاد تغییر شکل تا هنگام باربرداری را نشان میدهد . در زمان آنالیز ، اگر ضخامت ورق برابر با ضخامت شکستگی باشد ، آنگاه محدودیت شکلدهی فلنج بدست آمده است .
نتایج تجربی با نتایج شبیهسازی FEM مقایسه شدهاند . مشخص شده است که استفاده از FEM الاستوپلاستیک بطور مؤثری میتواند فرآیند ایجاد تغییر شکل تا زمان باربرداری را پیشبینی کند . هندسه محاسبه شده ورق و روابط بین بار و حرکت سوراخکن با دادههای تجربی مطابقت خوبی دارند .
کلمات کلیدی: الاستو- پلاستیک | روش المان محدود | سوراخکاری لبهدار و شکل دهی فلز.
حجم فایل: 1800 کیلوبایت
قیمت: 32400 تومان
توضیحات اضافی:
تعداد نظرات : 0