دانلود و نمایش مقالات مرتبط با gas turbine::صفحه 1
بلافاصله پس از پرداخت دانلود کنید

با سلام خدمت کاربران در صورتی که با خطای سیستم پرداخت بانکی مواجه شدید از طریق کارت به کارت (6037997535328901 بانک ملی ناصر خنجری ) مقاله خود را دریافت کنید (تا مشکل رفع گردد). 

نتیجه جستجو - gas turbine

تعداد مقالات یافته شده: 11
ردیف عنوان نوع
1 Performance assessment of a hybrid solid oxide and molten carbonate fuel cell system with compressed air energy storage under different power demands
ارزیابی عملکرد سیستم اکسید جامد ترکیبی و سیستم سلولی سوخت کربنات مذاب با ذخیره انرژی هوای فشرده تحت تقاضای توان مختلف-2020
As electricity demand can vary considerably and unpredictably, it is necessary to integrate energy storage with power generation systems. This study investigates a solid oxide and molten carbonate fuel cell system integrated with a gas turbine (GT) for power generation. The advanced adiabatic compressed air energy storage (AA-CAES) system is designed to enhance the system flexibility. Simulations of the proposed power system are performed to demonstrate the amount of power that can supply to the loads during normal and peak modes of operation under steady-state conditions. The pressure ratios of the GT and AACAES and the additional air feed are used to design the system and analyze the system performance. The results show that a small additional air feed to the GT is certainly required for the hybrid system. The GT pressure ratio of 2 provides a maximum benefit. The AA-CAES pressure ratio of 5 is recommended to spare some air in the storage and minimize storage volume. Moreover, implementation of the GT and AA-CAES into the integrated fuel cell system allows the system to cope with the variations in power demand.
Keywords: Solid oxide fuel cell | Molten carbonate fuel cell | Gas turbine | Compressed air energy storage | Energy management system
مقاله انگلیسی
2 First law thermodynamic analysis of the recuperated humphrey cycle for gas turbines with pressure gain combustion
تجزیه و تحلیل ترمودینامیکی قانون اول بهبود چرخه Humphrey برای توربین های گازی با احتراق افزایش فشار-2020
The current work is an analysis of the recuperated Humphrey cycle. Three cycle topologies are studied with and without turbine cooling. The study focuses on the interconnection between combustor pressure gain and heat recuperation. It is an attempt to optimize the cycle topology and configuration to achieve the maximum possible cycle efficiency. It is found that the best option to use recuperation in the Humphrey cycle is to operate the combustor at stoichiometric conditions, without preheating the air fed to it. The combustion air comes effectively form a compressor air bleed. The remaining air is further compressed at the combustor outlet pressure and is fed to a plenum between combustor and turbine once it is preheated by the recuperator. This cycle configuration results in the best performance both in terms of efficiency and specific work. Specifically, an efficiency increase between 2 and 5% points is achieved. This work concludes with a feasibility study for shockless explosion combustion (SEC) for the Humphrey cycle configurations and topologies that achieve an efficiency advantage against the Joule cycle. It is found that realistic SEC combustor lengths and efficiency gains can be simultaneously achieved, albeit not at the cycle configurations with the best performance.
Keywords: Pressure gain combustion | Humphrey cycle | Recuperation | Gas turbine | Emissions | Thermodynamic analysis
مقاله انگلیسی
3 Regional integrated energy system energy management in an industrial park considering energy stepped utilization
مدیریت انرژی سیستم انرژی یکپارچه منطقه ای در یک پارک صنعتی با توجه به استفاده پله ای از انرژی -2020
There are multiple energy demands in industrial parks. The industrial park’s energy system includes a variety of energy sources and energy-consuming equipment, with diverse load types and high reliability requirements for power supplies. And the situation of low energy utilization rates, unreasonable energy structures, great peak-to-valley power differences and the environment pollution needs to be improved. The application of multi-energy complementary regional integrated energy systems (RIES) can improve the performance of the industrial parks. Considering reasonable correspondence between the energy supply and demand in RIES, this paper proposes an RIES energy management strategy based on energy stepped utilization to further minimize the daily cost and make full use of the energy. Additionally, the piecewise linear model of gas turbine is established considering a part load ratio. According to the grade demands, the heat loads are divided into high-grade, middle-grade and low-grade heat loads and the load models are respectively established. The scenario reduction method is used to obtain typical scenarios in order to describe the randomness of weather factors. Finally, the simulation analysis shows that the proposed energy management method for the RIES can arrange the combination of gas turbines and output of devices more flexibly, and a more economical scheduling plan can be provided by this method. The high-grade and middle-grade energy are not only supplied to corresponding loads, but also can be converted into low-grade energy. Additionally, the stability and energy efficiency of the system are improved with the application of this strategy.
Keywords: Regional integrated energy system | Stepped utilization of energy | Mixed integer linear programming | Industrial park | Economic dispatching
مقاله انگلیسی
4 Dynamic energy conversion and management strategy for an integrated electricity and natural gas system with renewable energy: Deep reinforcement learning approach
استراتژی مدیریت و تبدیل انرژی پویا برای یک سیستم برق و گاز طبیعی یکپارچه با انرژی تجدید پذیر: رویکرد یادگیری تقویتی عمیق-2020
With the application of advanced information technology for the integration of electricity and natural gas systems, formulating an excellent energy conversion and management strategy has become an effective method to achieve established goals. Differing from previous works, this paper proposes a peak load shifting model to smooth the net load curve of an integrated electricity and natural gas system by coordinating the operations of the power-to-gas unit and generators. Moreover, the study aims to achieve multi-objective optimization while considering the economy of the system. A dynamic energy conversion and management strategy is proposed, which coordinates both the economic cost target and the peak load shifting target by adjusting an economic coefficient. To illustrate the complex energy conversion process, deep reinforcement learning is used to formulate the dynamic energy conversion and management problem as a discrete Markov decision process, and a deep deterministic policy gradient is adopted to solve the decision-making problem. By using the deep reinforcement learning method, the system operator can adaptively determine the conversion ratio of wind power, power-to-gas and gas turbine operations, and generator output through an online process, where the flexibility of wind power generation, wholesale gas price, and the uncertainties of energy demand are considered. Simulation results show that the proposed algorithm can increase the profit of the system operator, reduce wind power curtailment, and smooth the net load curves effectively in real time.
Keywords: Renewable energy accommodation | Dynamic energy conversion and management | Deep reinforcement learning
مقاله انگلیسی
5 فرآیند انتخاب مواد براساس ریسک که توسط تئوری اطلاعات حمایت می شود: مطالعه موردی توربین های گازی صنعتی
سال انتشار: 2017 - تعداد صفحات فایل pdf انگلیسی: 14 - تعداد صفحات فایل doc فارسی: 37
تیغه های توربین گازی با استفاده از مواد با مقاومت بالا در دمای بالا تولید می شوند، زیرا آنها در اغلب در معرض محیط های شدید قرار دارند. انتخاب مواد برای چنین مواردی باید با حساسیت و با استفاده از یک روش سیستماتیک انجام شود. علاوه بر این، ممکن است خطرات مختلفی در مورد ارزش های مواد مناسب وجود داشته باشد. به عنوان مثال، تفاوت بین شرایط طراحی شده و شرایط غیر منتظره ممکن است برخی از ویژگی های خطرناک را برای مواد ایجاد کند. اگرچه با توجه به خطراتی که برای مسئله انتخاب مواد تیغه توربین گاز یا موارد عملی مشابه با تکنولوژی بالا مورد توجه است، در چنین زمینه هایی شکاف تحقیقاتی وجود دارد. این مقاله الگوریتم انتخاب مواد مبتنی بر ریسک را با استفاده از اصول انتروپیهای سو و شانون که بر اساس نظریه اطلاعات پشتیبانی می شود، ارائه می دهد. در این راستا، رویکرد طراحی محوری فازی با ریسک را با ضرایب اهمیت یکپارچه شده شانون را توسعه می دهیم. یک مثال دنیای واقعی در مورد انتخاب مواد از تیغه توربین گازی صنعتی با استفاده از چهار تکنیک شامل طراحی محوری فازی، طراحی محوری فازی وزنی، طراحی محوری فازی بر پایه ریسک و رویکرد طراحی محوری وزنی مبتنی بر ریسک مورد بررسی قرار گرفته است. در مثال، عوامل ریسک برای تعیین تاثیر تغییرات دما در خواص مواد تعیین می شود. در نهایت، رتبه بندی های حاصل با محاسبه ضرایب همبستگی رتبه بندی Spearman مقایسه می شوند. مقایسه ها نشان می دهد که در نظر گرفتن عوامل خطر در مسئله بر روی رتبه بندی نتیجه تاثیر می گذارد. ما نتایج روش های پیشنهادی را با رویکردهای فازی بدون وزن و وزن دار MULTIMOORA معتبر سازی می کنیم.
مقاله ترجمه شده
6 Thermal efficiency of direct, inverse and sCO2 gas turbine cycles intended for small power plants
بازده حرارتی مستقیم، معکوس و چرخه توربین گاز sCO2 در نظر گرفته شده برای نیروگاه های انرژی کوچک-2016
The aim of this paper is to study whether the efficiency loss that takes place at low Reynolds numbers (Re) can be a problem for small power gas turbines and, if this is the case, to assess whether the use of alternative power cycles such as supercritical sCO2 or inverse JouleeBrayton cycles might solve this problem.First, two different methods for the estimation of the Reynolds efficiency loss are explained and compared. Then, the design parameters of a number of existing commercial gas turbines are used in order to show that this efficiency loss begins to be significant when the shaft power is lower than about1.5 MW. Efficiency and Re calculations are carried out subsequently for inverse and sCO2 1 MW cycles intended for medium range temperatures. For such small powers, the supercritical sCO2 closed loop Brayton cycle seems to be a promising alternative, as the Reynolds number experiences an increase due to the high fluid density. Also, sCO2 cycles achieve good efficiencies due to the compressor work reduction obtained near the critical point. The inverse cycle is a less interesting option because its ef- ficiency is low and there is no significant improvement in the Reynolds number.© 2016 Elsevier Ltd. All rights reserved.
Keywords: Low Reynolds number | Small gas turbine | sCO2 cycle | Scaling down | as turbines
مقاله انگلیسی
7 Transient probabilistic analysis for turbine blade-tip radial clearance with multi-component and multi-physics fields based on DCERSM
تجزیه و تحلیل احتمالاتی گذرا برای توربین های تیغه نوک فاصله شعاعی چند محفظه ای و چند فیزیکی مبتنی بر اساس DCERSM-2016
Against the background of the probabilistic analysis for High Pressure Turbine (HPT) Blade-tip Radial Running Clearance (BRRC) to achieve the high-performance and high-reliability of aeroengine, Distributed Collaborative Extremum Response Surface Method (DCERSM) was proposed for the dynamic probabilistic analysis of complex turbomachinery on the foundation of quadratic polynomials response surface model. On the basis of deeply investigating Extremum Response Surface Method (ERSM), the mathematical model of DCERSM was established based on quadratic polynomial function. As illustrated in BRRC transient probabilistic analysis with multiple components and multi-physics fields based on DCERSM, blade-tip radial static clearance δ = 1.82 mm is advisable synthetically considering the reliability and working efficiency of gas turbine. The reliability, distribution characteristics and failure probability of BRRC are obtained. Besides, rotational speed ω and gas temperature T are the most important factors and expansivity coefficients and surface coefficients of heat transfer show also important influence on BRRC variation. Through the comparison of three methods (DCERSM, ERSM, Monte Carlo method), it is demonstrated that DCERSM reshapes the possibility of complex turbomachinery probabilistic analysis and improves computing efficiency while preserving the accuracy. DCERSM offers a useful insight for BRRC dynamic reliability design and optimization with multi-object and multi-discipline. The efforts of this study also enrich the theory and method of mechanical reliability design.
Keywords: High pressure turbine | Blade-tip radial running clearance | Dynamic probabilistic analysis | Distributed collaborative extremum | response surface method | Multi-object multi-disciplinary
مقاله انگلیسی
8 Numerical and Experimental Investigation on the Performance of Lean Burn Catalytic Combustion for Gas Turbine Application
بررسی عددی و تجربی بر روی کارایی سوختگی ناب کاتالیستی احتراق برای کاربرد توربین گاز-2015
This manuscript presents our numerical and experimental results regarding the performance characteristics of lean burn catalytic combustion for gas turbine application. The reactant transport was assumed to be controlled by both bulk diffusion as well as surface kinetics, implemented by means of an approximate reaction rate equation and empirical coefficients to incorporate reaction mechanism. Experimental and numerical results were compared to examine the effects of methane mole fraction, inlet temperature, operating pressure, velocity and hydrogen species on combustion intensity. The results indicate that inlet temperature is the most significant parameter that impacts operation of the catalytic combustor and the most effective methods for improving the methane conversion are increasing the inlet temperature and increasing the methane mole fraction. Simulations from 1D heterogeneous plug flow model can capture the trend of catalytic combustion and describe the behavior of the catalytic monolith in detail. The addition of hydrogen will provide heat release by the exothermic combustion reaction so that the reactants reach a temperature at which methane oxidation can light-off. Keywords: Lean burn catalytic combustion; performance; gas turbine
مقاله انگلیسی
9 ارزیابی ریسک حالات خرابی جداره دیفیوزر گاز توربین گازی سیمنز V94:2 با روش FMEA
سال انتشار: 2012 - تعداد صفحات فایل pdf انگلیسی: 8 - تعداد صفحات فایل doc فارسی: 13
خرابی اتصال جوشی جدار‌ة دیفیوزر گاز و محفظه اگزوز یکی از حالات خرابی توربین گازی V94.2 است که در برخی نیروگاه اتفاق افتاده است. زمانی که مشتریان می‌خواهند آخرین سفارش این محصول را بپذیرند این نقص یکی از ابهاماتشان بشمار می‌رود. بر همین اساس، اولویت ریسک این خرابی براساس روش آنالیز حالات خرابی (FMEA) ارزیابی می‌شود تا مشخص شود این خرابی برای عملکرد توربین فاجعه‌آمیز و برای انسان مضر است یا خیر. با استفاده از تاریخچه ۱۱۰ توربین گازی از این مدل که در برخی نیروگاه‌ها استفاده می‌شدند، عدد شدت، عدد رخداد و عدد تشخیص خرابی مشخص‌شده و در نتیجه عدد اولویت ریسک (RPN) خرابی تعیین شد. در نهایت، ماتریس بحرانی خرابی‌های بالقوه تشکیل شد و نشان داد که حالات خرابی در منطق‌ة ایمن قرار دارند.
مقاله ترجمه شده
10 تاثیر نسبت گرماهای ویژه بر روی یک سیکل برایتونِ مقیاس کوچک
سال انتشار: 2012 - تعداد صفحات فایل pdf انگلیسی: 8 - تعداد صفحات فایل doc فارسی: 14
چکیده انرژی خورشیدی متمرکز شده را می توان برخلاف صفحه های حرارتی- خورشیدی متداول، به عنوان یک منبع حرارتی سیکل برایتون در نظر گرفت. که این منبع، انرژی خورشیدی را به منظور تولید بخار برای راندن توربین متمرکز می کند. سیکل برایتون از آب استفاده نمی کند. در عوض انرژی خورشیدی متمرکز به منظور حرارت دادن گاز استفاده می شود که به عنوان واسطه کار می کند و این گاز در یک توربین گازی به منظور تولید توان انبساط می یابد. مزیت عمده سیکل برایتون پتانسیل آن برای عملکرد پایین و هزینه نگهداری پایین می باشد و همچنین موتورهایی است که برای کاربردهای توان با سایز بالا و و سایز پایین در نظر گرفته می‌شود. هنگامی که اتلافات فشاری که در سیکل برایتون دارای بازیاب رخ می دهد، در نظر گرفته می شود، بازدهی سیکل به نسبت گرماهای ویژه سیال، ضریب اتلاف فشار و نسبت مینیمم دما به ماکزیمم دما وابسته است. با استفاده از یک روش تحلیلی عددی، مشخصات بازدهی یک سیکل برایتون بسته با بازیاب تحت شرایط مختلفی از نسبتهای گرماهای ویژه و در دماهای عامل مختلف از سیال مورد مطالعه قرار گرفته شد. سه سیال عامل مختلف، به نامهای، هلیوم، تترافلورومتان(CF4 یا رفریگرانت-14، غیر سمی و غیر قابل اشتعال) و هوا آنالیز شدند و برای یک سیکل برایتون بسته با بازیاب و سایز کوچک مورد مقایسه قرار گرفتند. دما نیز در حدی پایین آورده شده که می توان راحتتر توسط انرژی خورشیدی به آن دست یافت. مشاهده شد که یک بازدهی حرارتی بهینه وجود دارد و به نسبت فشار کمپرسور بهینه مربوط به سیالهای عامل مختلف ، مربوط می شود. تاثیر نسبت گرماهای ویژه و نسبت دمای سیکل بازدهی حرارتی سیکل مورد بررسی قرار گرفتند. کلمات کلیدی: خورشید، سیکل برایتون، نسبت گرمای ویژه
مقاله ترجمه شده
rss مقالات ترجمه شده rss مقالات انگلیسی rss کتاب های انگلیسی rss مقالات آموزشی
logo-samandehi
بازدید امروز: 42 :::::::: بازدید دیروز: 0 :::::::: بازدید کل: 42 :::::::: افراد آنلاین: 47