دانلود و نمایش مقالات مرتبط با نانوسیال::صفحه 1
بلافاصله پس از پرداخت دانلود کنید

با سلام خدمت کاربران در صورتی که با خطای سیستم پرداخت بانکی مواجه شدید از طریق کارت به کارت (6037997535328901 بانک ملی ناصر خنجری ) مقاله خود را دریافت کنید (تا مشکل رفع گردد). 

نتیجه جستجو - نانوسیال

تعداد مقالات یافته شده: 15
ردیف عنوان نوع
1 Electrical and acoustic investigation of partial discharges in two types of nanofluids
بررسی الکتریکی و صوتی تخلیه جزئی در دو نوع نانوسیال-2021
Measurements of partial discharges in liquid dielectrics are important for prediction of a serious failure of electrical equipment. Recent research findings show that application of nanoparticles in dielectric liquids may increase their resistance to partial discharges. However, physical properties of a host liquid are expected to play a decisive role in the effective suppression of partial discharges by nanoparticles. In this paper, a transformer oil prepared by a gas-to-liquid technology and a standard naphthenic transformer oil are doped with an equal amount of iron oxide nanoparticles. Determination of basic physical properties of the oils and the nanofluids is followed by an experimental investigation of partial discharges under various alternating voltage levels. The detection of partial discharges is approached by two independent methods, electrically and acoustically. Both methods revealed occurrence of partial discharges in the gasto-liquid oil at higher voltages, as compared with the naphthenic oil. Acoustic emission energy is found one order of magnitude greater in the gas-to-liquid oil than in the naphthenic oil. The acoustic wave propagation dependence on the physical properties of the liquid is considered in the qualitative explanation of the observed phenomenon. The presence of nanoparticles can suppress partial discharges in the naphthenic oil, but not in the gas-to-liquid oil.
Keywords: Liquid dielectric | Partial discharge | Ferrofluids | Transformer oil | Acoustic emission | Magnetic nanoparticles
مقاله انگلیسی
2 Flow and heat transfer past a permeable power-law deformable plate with orthogonal shear in a hybrid nanofluid
انتقال جریان و حرارت از یک صفحه قابل تغییر قدرت قانون با برشی متعامد در یک نانوسیال ترکیبی-2020
This study concerns the three-dimensional hybrid nanofluid flow and heat transfer due to a deformable (stretching/shrinking) plate with power-law velocity and orthogonal surface shear. The flow due to the shrinking sheet is maintained with the imposition of wall mass suction. The effect of adding Cu and Al2O3 nanoparticles are represented by a homogeneous mixture model with the modified thermophysical properties. Two types of thermophysical properties for hybrid nanofluids are discussed and compared in this interesting work. The three-dimensional model is then, reduced into a relevant set of ordinary differential equations using similarity transformation. The results are generated using the bvp4c solver and presented in the tables and graphs. Duality of solutions are observed in both stretching and shrinking regions, however, only the first solution is proved to be stable and realistic. Surprisingly, the heat transfer rate augments when the power law velocity is used. The hybrid nanofluid with an upsurge of copper volume fraction also reduces the rate of heat transfer.
KEYWORDS : Stretching/shrinking surface | Three dimensional | Hybrid nanofluid | Heat transfer | Dual solutions
مقاله انگلیسی
3 Employing V-shaped ribs and nanofluid as two passive methods to improve second law characteristics of flow within a square channel: A two-phase approach
استفاده از دنده های V شکل و نانوسیال به عنوان دو روش غیرفعال برای بهبود ویژگی های قانون دوم جریان در یک کانال مربع: یک روش دو فاز-2020
This research attempts to investigate the effects of simultaneous utilization of V-shaped ribs and nanofluid as two heat transfer enhancement approaches inside a square channel on the second law at- tributes. For this purpose, the comprehensive entropy generation and exergy destruction analyses are car- ried out with the aid of the two-phase mixture technique for the copper–water nanofluid flow through the channel enhanced with the 45 °V-shaped ribs. Firstly, a comparison is made between attack angles of 45 °and 60 °, which unveils the superiority of 45 °because it shows lower entropy generation. The Cu nanoparticles are utilized as the main nanoparticles. Furthermore, the nanofluids containing the Ag nanoparticles are also simulated at two volume fractions of 0.01 and 0.03 to make comparison between different nanoparticle materials. The impacts of rib configuration including the rib pitch and its height are assessed using three rib pitches and three rib heights. The total entropy generation and total exergy destruction decrease as the volume fraction increases, such that an around 31.85% reduction occurs in the total entropy generation and total exergy destruction when the volume fraction increases by 0.03 for the case of rib height of 5 mm and rib pitch of 100 mm. Thereby, the second law efficiency rises by 15.64% in the same condition. Additionally, the installed 45 °V-shaped ribs remarkably contribute to the total irreversibility reduction by means of creating four recirculation flows and powerful swirl flows. The re- sults indicate that utilizing both larger rib height and smaller rib pitch (at the same time) exhibits lower exergy destruction and enhances the second law efficiency.
Keywords: Two-phase mixture model | second law efficiency | v-shaped rib | entropy generation | nanofluid | exergy destruction
مقاله انگلیسی
4 CFD analysis of second law characteristics for flow of a hybrid biological nanofluid under rotary motion of a twisted tape: Exergy destruction and entropy generation analyses
تجزیه و تحلیل CFD از ویژگی های قانون دوم برای جریان یک نانوسیالات بیولوژیکی ترکیبی تحت حرکت چرخشی نوار پیچ خورده: تخریب اگزرژی و تجزیه و تحلیل نسل آنتروپی-2020
The main goal of the current study is to evaluate the effects of a hybrid heat transfer enhancement method, i.e. simultaneous deployment of active and passive techniques, with employing an ecofriendly-produced graphene nanoplatelets nanofluid from the viewpoint of the second law of thermodynamics. The numerical simulations are performed for the tubes enhanced with the innovative rotary twisted tape. Employing the rotary twisted tape intensifies the flow mixing, disrupts the thermal boundary layer, and reduces the temperature gradients dramatically. The total entropy generation and total exergy destruction of nanofluid extremely diminish by the rotational speed elevation. The maximum decrement in the total entropy generation is 87.38%, which occurs by elevating the rotational speed from 0 to 900 rpm. The concentration increase considerably contributes to the exergy destruction decrement besides total entropy generation reduction. The lower twisted ratio exhibits the smaller thermal irreversibility, and the best second law efficiency equals to 0.932.
Keywords: Exergy destruction | Rotational twisted tape | Graphene nanoplatelets nanofluid | Entropy generation | Ecofriendly nanofluid | Second law efficiency
مقاله انگلیسی
5 Using of Artificial Neural Networks (ANNs) to predict the thermal conductivity of Zinc Oxide–Silver (50%–50%)/Water hybrid Newtonian nanofluid
استفاده از شبکه های عصبی مصنوعی (ANN) برای پیش بینی هدایت حرارتی روی اکسید-نقره روی (50٪ -50٪) / نانوسیال نیوتنی ترکیبی آب-2020
In this study, after generating experimental data points of Zinc Oxide (ZnO)–Silver (Ag) (50%–50%)/Water nanofluid, an algorithm is proposed to calculate the best neuron number in the Artificial Neural Network (ANN), and the performance and correlation coefficient for ANN has been calculated. Then, using the fitting method, a surface is fitted on the experimental data, and the correlation coefficient and performance of this method have been calculated. Finally, the absolute values of errors in both methods have been compared. It can be seen that the best neuron number in the hidden layer is 7 neurons. We concluded that both methods could predict the behavior of nanofluid, but the fitting method had smaller errors. Also, the ANN method had better ability in predicting the thermal conductivity of nanofluid based on the volume fraction of nanoparticles and temperature. Finally, we found that, in ANN, all outputs, the maximum absolute value of error is 0.0095, and the train performance is 1.6684e-05.
Keywords: Artificial Neural Networks (ANNs) | Thermal conductivity | Hybrid Newtonian nanofluid
مقاله انگلیسی
6 شبیه‌سازی CFD یک جوشش جریانی نانوسیال نمک غلیظ در یک لوله‌ی مستطیلی شکل
سال انتشار: 2018 - تعداد صفحات فایل pdf انگلیسی: 11 - تعداد صفحات فایل doc فارسی: 37
قابلیت نانوسیال‌ها در بهبود انتقال حرارت و شار حرارتی بحرانی (CHF) در جوشش استخری شناخته شده است. جوشش جریانی معمولا به‌وسیله‌ی روابط انتقال حرارت بررسی می‌شوند. اما در مورد نانوسیال محلول نمک غلیظ، این روابط مناسب نیست. یک مدل با استفاده از کد تجاری CFD و با توابع تعریف شده‌ توسط کاربر توسعه داده شده است؛ (UDF) برای این مورد معرفی می‌شود تا گرما و انتقال جرم را در مجرای بویلر برای بخار جاذب تبرید تعیین کند. شبیه‌سازی دینامیک سیالات محاسباتی (CFD) برای بررسی تأثیرات کسرهای حجمی متغییر، سرعت سیال و دمای بویلر بر روی جوشش و مشخصه‌های تغییرات فاز در سیستم ارائه شده است. در این تحقیق، چهار فاز یعنی استون مایع، استون بخار، محلول ZnBr2/استون مایع و نانوذرات جامد مورد آزمایش قرار گرفته‌اند. نانوذرات اکسید روی به‌‌‌عنوان فاز شبه‌سرد در مخلوط عمل می‌کنند. علاوه بر این، این مطالعه، پارامترهای کلیدی بر روی سیستم نانوسیال، رفتار فازها و تأثیرات مؤلفه‌های مختلف وقتی که مؤلفه‌های جزئی نبخیر می‌شوند را ارزیابی می‌کند. در پژوهش قبلی، از آب به‌عنوان سیال پایه در مبردها و سیالات انتقال حرارت استفاده شده بود. در این تحقیق، فرآیند با استفاده از نرم‌افزار انسیس فلوئنت نسخه 15 و مدل جریان چندفازی مخلوط، مدل‌سازی شده است؛ همچنین از روش حجم سیالی (VOF) برای بررسی رفتار فاز بخار استفاده شده است. از UDF مورد استفاده در پژوهش (لی، 1980) برای جوشش نانوسیالات بهره گرفته شده است تا انتقال جرم را بر روی جوشش مدل کند. نتایج نشان داد که افزایش بارگذاری نانوسیالات (صفر، 1/0، 3/0، 5/0 و 1 درصد حجمی) منجر به افزایش کسر حجی بخار و ضریب انتقال حرارت می‌شود. این موضوع به این دلیل است که افزایش انتقال حرارت سیستم منجر به زیاد شدن هدایت حرارتی نانوسیال می‌شود. زیاد شدن دمای بویلر (330، 333 و 335 کلوین) باعث افزایش کسر حجمی بخار و ضریب انتقال حرارت می‌شود چون زمانی که فرآیند هنوز در مرحله‌ی جوشش هسته‌ای است، شار حرارتی با افزایش اختلاف دما بیشتر می‌گردد. این روش جدید برای سیستم چهار فازی می‌تواند، جوشش نانوسیال محلول نمک غلیظ را تعیین کند.
کلمات کلیدی: استون- ZnBr2 | ZnO | نانوسیال | جوشش | CFD | انتقال حرارت | انتقال جرم | لوله‌ی مستطیلی شکل | تغییر فاز.
مقاله ترجمه شده
7 مطالعه‌ی انتقال حرارت به‌وسیله‌ی جابجایی طبیعی نانوسیال‌ها در یک محفظه‌ی استوانه‌ای نسبتا گرم شده
سال انتشار: 2018 - تعداد صفحات فایل pdf انگلیسی: 10 - تعداد صفحات فایل doc فارسی: 21
در این تحقیق، یک مطالعه‌ی عددی بر روی انتقال حرارت جابجایی طبیعی دو نانوسیال در یک محفظه‌ی استوانه‌ای که به‌صورت نسبی گرم شده، انجام گرفته است. گرمایش نسبی در سمت پایین محفظه در دمای ثابت اتفاق می‌افتد. طول منبع گرم از 5% تا 25% در همه‌ی پیرامون محفظه تغییر می‌کند. دمای دو بخش جانبی محفظه در دمای پایین ثابت نگه داشته می‌شود که طول هر کدام از آنها، 25% محیط نهایی است. قسمت بالایی محفظه آدیاباتیک در نظر گرفته می‌شود که طول آن نیز برابر با 25% محیط نهایی می‌باشد. از دو نانوسیال آب- Cu و آب- TiO2 با کسرهای حجمی متفاوت که در محدوده‌ی صفر الی 05/0 تغییر می‌کنند، استفاده شده است. عدد رایلی نیز در بازه‌ی 103 تا 106 متغیر است. نتایج به‌دست آمده، به‌طور خلاصه در قالب روابط همبستگی برای عدد ناسلت میانگین که تابعی از طول گرمایش، عدد رایلی و کسر حجمی برای هر دو نانوذره می‌باشد، ارائه شده است.
کلمات کلیدی: جابجایی طبیعی | محفظه‌ی استوانه‌ای افقی | گرمایش نسبی | حجم محدود | نانوسیال.
مقاله ترجمه شده
8 خصوصیات حرارتی نانوسیال های هیبریدی
سال انتشار: 2018 - تعداد صفحات فایل pdf انگلیسی: 9 - تعداد صفحات فایل doc فارسی: 14
تحقیقات انجام ‌شده بر روی نانو سیالات در دهه های گذشته به سرعت گسترش یافته است. نانوسیال ها نزدیکی (همانندی) فوری در کاربردهای مبدل حرارتی را با ویژگی‌های امیدبخش خود کشف کرده‌اند که با توجه به پیش‌نیازهای آن‌ها می توان آن را کنترل نمود. علاوه بر این، متخصصین به تلاش برای استفاده از نانوسیال های ترکیبی در سالیان اخیر، که با معلق سازی نانوذرات مختلف در یک ترکیب یا قاب مرکب در مایع پایه طراحی شده ‌است، تلاش های گسترده ای کرده‌اند. یک مطالعه تجربی برای بررسی خواص ترمو - فیزیکی مس - تیتانیوم و نانوسیال های هیبریدی انجام شده است. این اثر سنتز نانوذرات هیبرید Cu – TiO2، آماده‌ سازی نانوسیال و خصوصیات گرمایی آن‌ها با غلظت‌های مختلف (0.1٪، 0.2٪، 0.3٪ و 0.4٪) در دو دمای مختلف 30O و 60O درجه را توضیح می‌دهد. نتایج این کار نشان می‌دهد که رسانایی گرمایی و ویسکوزیته با افزایش درصد Cu-TiO2 به حالت مایع افزایش می‌یابد.
کلمات کلیدی : تراکم (چگالی) | نانوسیال هیبریدی | رسانایی (هدایت) حرارتی | ویسکوزیته و غلظت حجم
مقاله ترجمه شده
9 انتقال گرمای نانو سیال بین دو لوله با در نظر گرفتن حرکت براونی با استفاده از روش AGM
سال انتشار: 2017 - تعداد صفحات فایل pdf انگلیسی: 7 - تعداد صفحات فایل doc فارسی: 18
جریان نانو سیال بین دو لوله با مقطع دایره‌ای در حضور میدان مغناطیسی موردمطالعه قرارگرفته است. از مدل KKL برای نانو سیال‌ها استفاده‌شده است. اثر تشعشع گرمایی در معادله‌ی انرژی در نظر گرفته‌شده است. از AGM هم برای حل معادلات دیفرانسیل معمولی استفاده‌شده است. روش‌های شبه تحلیلی برای پارامترهای مختلفی ازجمله ضریب منظری، عدد هارتمن، عدد اکرت و عدد رینولدز موردبررسی قرارگرفته است. نتایج مشخص می‌کند که گرادیان دما با افزایش عدد هارتمن، اکرت و ضریب منظری افزایش‌یافته ولی با افزایش عدد رینولدز کاهش می‌یابد. سرعت با افزایش نیروهای لورنتس کاهش می‌یابد ولی با بالا رفتن عدد رینولدز افزایش می‌یابد.
مقاله ترجمه شده
10 جریان نانوسیال و انتقال گرما در حفره با میدان مغناطیسی متغیر
سال انتشار: 2017 - تعداد صفحات فایل pdf انگلیسی: 11 - تعداد صفحات فایل doc فارسی: 16
جریان نانوسیال Fe3o4 در یک حفره با شار گرمای ثابت با استفاده از کنترل حجم بر اساس روش المان محدود بررسی و تحقیق می شود. اثرات Rayleigh و Hartmann و کسر حجمی Fe3o4 ( نانومغناطیس و اکسید آهن ) روی ویژگی های جریان و انتقال گرما تحلیل و بررسی شد. نتایج نشان می دهد که شیب دما یک عملکرد افزایشی از نیروهای شناور و کسر حجمی این ماده است ؛ اما یک عملکرد کاهشی از نیروهای لورنتس است. همچنین نرخ انتقال گرما با افزایش در نیروهای لورنتس تقویت می شود. اگرچه عکس آن در مورد نیروهای نرخ انتقال گرما با نیروهای شناوری است. علاوه براین با افزایش نیروهای لورنتس جریان اصلی به سمت پایین حرکت می کند. همچنین انتظار می رود نتایجی که اینجا ارائه می شود ، نه تنها اطلاعات مفیدی در مورد خنک کردن اجزای الکتریکی فراهم می کند بلکه مرور ادبیات حاضر را تکمیل می کند.
مقاله ترجمه شده
rss مقالات ترجمه شده rss مقالات انگلیسی rss کتاب های انگلیسی rss مقالات آموزشی
logo-samandehi
بازدید امروز: 9468 :::::::: بازدید دیروز: 0 :::::::: بازدید کل: 9468 :::::::: افراد آنلاین: 72